/usr/share/doc/postfix/CDB_README is in postfix-doc 3.1.0-3.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 | PPoossttffiixx CCDDBB HHoowwttoo
-------------------------------------------------------------------------------
IInnttrroodduuccttiioonn
CDB (Constant DataBase) is an indexed file format designed by Daniel Bernstein.
CDB is optimized exclusively for read access and guarantees that each record
will be read in at most two disk accesses. This is achieved by forgoing support
for incremental updates: no single-record inserts or deletes are supported. CDB
databases can be modified only by rebuilding them completely from scratch,
hence the "constant" qualifier in the name.
Postfix CDB databases are specified as "cdb:name", where name specifies the CDB
file name without the ".cdb" suffix (another suffix, ".tmp", is used
temporarily while a CDB file is under construction). CDB databases are
maintained with the postmap(1) or postalias(1) command. The DATABASE_README
document has general information about Postfix databases.
CDB support is available with Postfix 2.2 and later releases. This document
describes how to build Postfix with CDB support.
BBuuiillddiinngg PPoossttffiixx wwiitthh CCDDBB ssuuppppoorrtt
These instructions assume that you build Postfix from source code as described
in the INSTALL document. Some modification may be required if you build Postfix
from a vendor-specific source package.
Postfix is compatible with two CDB implementations:
* The original cdb library from Daniel Bernstein, available from http://
cr.yp.to/cdb.html, and
* tinycdb (version 0.5 and later) from Michael Tokarev, available from http:/
/www.corpit.ru/mjt/tinycdb.html.
Tinycdb is preferred, since it is a bit faster, has additional useful
functionality and is much simpler to use.
To build Postfix after you have installed tinycdb, use something like:
% make tidy
% CDB=../../../tinycdb-0.5
% make -f Makefile.init makefiles "CCARGS=-DHAS_CDB -I$CDB" \
"AUXLIBS_CDB=$CDB/libcdb.a"
% make
Alternatively, for the D.J.B. version of CDB:
% make tidy
% CDB=../../../cdb-0.75
% make -f Makefile.init makefiles "CCARGS=-DHAS_CDB -I$CDB" \
"AUXLIBS_CDB=$CDB/cdb.a $CDB/alloc.a $CDB/buffer.a $CDB/unix.a $CDB/
byte.a"
% make
Postfix versions before 3.0 use AUXLIBS instead of AUXLIBS_CDB. With Postfix
3.0 and later, the old AUXLIBS variable still supports building a statically-
loaded CDB database client, but only the new AUXLIBS_CDB variable supports
building a dynamically-loaded or statically-loaded CDB database client.
Failure to use the AUXLIBS_CDB variable will defeat the purpose of dynamic
database client loading. Every Postfix executable file will have CDB
database library dependencies. And that was exactly what dynamic database
client loading was meant to avoid.
After Postfix has been built with cdb support, you can use "cdb" tables
wherever you can use read-only "hash", "btree" or "dbm" tables. However, the
"ppoossttmmaapp --ii" (incremental record insertion) and "ppoossttmmaapp --dd" (incremental
record deletion) command-line options are not available. For the same reason
the "cdb" map type cannot be used to store the persistent address verification
cache for the verify(8) service, or to store TLS session information for the
tlsmgr(8) service.
|