/lib/firmware/isci/create_fw.h is in linux-firmware 1.157.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 | #ifndef _CREATE_FW_H_
#define _CREATE_FW_H_
#include "probe_roms.h"
/* we are configuring for 2 SCUs */
static const int num_elements = 2;
/*
* For all defined arrays:
* elements 0-3 are for SCU0, ports 0-3
* elements 4-7 are for SCU1, ports 0-3
*
* valid configurations for one SCU are:
* P0 P1 P2 P3
* ----------------
* 0xF,0x0,0x0,0x0 # 1 x4 port
* 0x3,0x0,0x4,0x8 # Phys 0 and 1 are a x2 port, phy 2 and phy 3 are each x1
* # ports
* 0x1,0x2,0xC,0x0 # Phys 0 and 1 are each x1 ports, phy 2 and phy 3 are a x2
* # port
* 0x3,0x0,0xC,0x0 # Phys 0 and 1 are a x2 port, phy 2 and phy 3 are a x2 port
* 0x1,0x2,0x4,0x8 # Each phy is a x1 port (this is the default configuration)
*
* if there is a port/phy on which you do not wish to override the default
* values, use the value assigned to UNINIT_PARAM (255).
*/
/* discovery mode type (port auto config mode by default ) */
/*
* if there is a port/phy on which you do not wish to override the default
* values, use the value "0000000000000000". SAS address of zero's is
* considered invalid and will not be used.
*/
#ifdef MPC
static const int mode_type = SCIC_PORT_MANUAL_CONFIGURATION_MODE;
static const __u8 phy_mask[2][4] = { {1, 2, 4, 8},
{1, 2, 4, 8} };
static const unsigned long long sas_addr[2][4] = { { 0x5FCFFFFFF0000001ULL,
0x5FCFFFFFF0000002ULL,
0x5FCFFFFFF0000003ULL,
0x5FCFFFFFF0000004ULL },
{ 0x5FCFFFFFF0000005ULL,
0x5FCFFFFFF0000006ULL,
0x5FCFFFFFF0000007ULL,
0x5FCFFFFFF0000008ULL } };
#else /* APC (default) */
static const int mode_type = SCIC_PORT_AUTOMATIC_CONFIGURATION_MODE;
static const __u8 phy_mask[2][4];
static const unsigned long long sas_addr[2][4] = { { 0x5FCFFFFF00000001ULL,
0x5FCFFFFF00000001ULL,
0x5FCFFFFF00000001ULL,
0x5FCFFFFF00000001ULL },
{ 0x5FCFFFFF00000002ULL,
0x5FCFFFFF00000002ULL,
0x5FCFFFFF00000002ULL,
0x5FCFFFFF00000002ULL } };
#endif
static const int cable_selection[2][4];
/* Maximum number of concurrent device spin up */
static const int max_num_concurrent_dev_spin_up = 1;
/* enable of ssc operation */
/*
* NOTE: also see probe_roms.h. This value can be set for ssc values.
* Values can be set for:
* ssc_sata_tx_spread_level
* ssc_sas_tx_spread_level
* ssc_sas_tx_type
*/
static const __u8 enable_ssc;
/* AFE_TX_AMP_CONTROL */
static const unsigned int afe_tx_amp_control0 = 0x000bdd08;
static const unsigned int afe_tx_amp_control1 = 0x000ffc00;
static const unsigned int afe_tx_amp_control2 = 0x000b7c09;
static const unsigned int afe_tx_amp_control3 = 0x000afc6e;
static const char blob_name[] = "isci_firmware.bin";
static const char sig[] = "ISCUOEMB";
static const unsigned char version = ISCI_ROM_VER_LATEST;
#endif
|