/var/lib/pcp/testsuite/326 is in pcp-testsuite 3.8.12ubuntu1.
This file is owned by root:root, with mode 0o755.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 | #! /bin/sh
# PCP QA Test No. 326
# Check PMCD state change notification, aka PMCD reset
#
# Copyright (c) 1995-2002 Silicon Graphics, Inc. All Rights Reserved.
#
seq=`basename $0`
echo "QA output created by $seq"
# get standard filters
. ./common.product
. ./common.filter
. ./common.check
signal=$PCP_BINADM_DIR/pmsignal
status=1
done_clean=false
LOCALHOST=`hostname`
[ $PCP_VER -lt 3806 ] && LOCALHOST=`echo $LOCALHOST | sed -e 's/\..*//'`
_cleanup()
{
if $done_clean
then
:
else
echo
echo "Restore pmcd.conf and restart PMCD ..."
[ -f $tmp.pmcd.conf ] && $sudo mv $tmp.pmcd.conf $PCP_PMCDCONF_PATH
_restore_primary_logger
$sudo $PCP_RC_DIR/pcp restart | _filter_pcp_start
rm -f $tmp.*
_wait_for_pmcd
_wait_for_pmlogger
done_clean=true
fi
exit $status
}
$sudo rm -rf $tmp.* $seq.full
trap "_cleanup" 0 1 2 3 15
_filter_host()
{
# filter this, as we now fetch pmcd.hostname, sneakily
sed \
-e "/ value \"$REALHOST\"/d" \
-e "/ value \"$LOCALHOST\"/d"
}
_filter_pmval()
{
sed \
-e '1,/^interval:/d' \
-e 's/[0-9][0-9]:[0-9][0-9]:[0-9][0-9]\.[0-9][0-9][0-9]/TIMESTAMP/g' \
| $PCP_AWK_PROG '
/No values available/ { print; next }
0 <= $2 && $2 < 1.1 { $2 = "non-negative number, less than 1.1" }
{ print }' \
| uniq
}
trap "_cleanup" 0 1 2 3 15
rm -f $seq.full
# real QA test starts here
PMDA_PMCD_PATH=$PCP_PMDAS_DIR/pmcd/pmda_pmcd.$DSO_SUFFIX
# copy the pmcd config file to restore state later.
cp $PCP_PMCDCONF_PATH $tmp.pmcd.conf
# start from a known starting point
$sudo $PCP_RC_DIR/pcp stop >/dev/null 2>&1
cat <<End-of-File >$tmp.tmp
# temporary for qa/$seq
pmcd 2 dso pmcd_init $PMDA_PMCD_PATH
sample 29 pipe binary $PCP_PMDAS_DIR/sample/pmdasample -d 29
End-of-File
$sudo cp $tmp.tmp $PCP_PMCDCONF_PATH
_writable_primary_logger
$sudo $PCP_RC_DIR/pcp restart | _filter_pcp_start
_wait_for_pmcd
if [ -d $PCP_LOG_DIR/pmlogger ]
then
LOGGING_DIR=$PCP_LOG_DIR/pmlogger
else
LOGGING_DIR=$PCP_LOG_DIR
fi
_wait_for_pmlogger -P $LOGGING_DIR/$LOCALHOST/pmlogger.log
echo 'connect primary
log mandatory on 500 msec { pmcd.numagents sample.milliseconds }' \
| pmlc
# run for 20 seconds
pmval -s 40 -t 0.5 -D fetch pmcd.numagents >$tmp.pmval 2>&1 &
sleep 3
echo "=== kill sample PMDA process ==="
$sudo $signal -a -s TERM pmdasample
pminfo -v sample >/dev/null 2>&1
sleep 3
echo "=== SIGHUP PMCD ==="
$sudo $signal -a -s HUP pmcd
sleep 3
echo "=== drop sample PMDA, like Remove ==="
cat <<End-of-File >$tmp.tmp
# temporary for qa/$seq
pmcd 2 dso pmcd_init $PMDA_PMCD_PATH
End-of-File
$sudo cp $tmp.tmp $PCP_PMCDCONF_PATH
$sudo $signal -a -s HUP pmcd
sleep 3
echo "=== add sample PMDA, like Install ==="
cat <<End-of-File >$tmp.tmp
# temporary for qa/$seq
pmcd 2 dso pmcd_init $PMDA_PMCD_PATH
sample 29 pipe binary $PCP_PMDAS_DIR/sample/pmdasample -d 29
End-of-File
$sudo cp $tmp.tmp $PCP_PMCDCONF_PATH
$sudo $signal -a -s HUP pmcd
sleep 3
wait
# if desperate!
#echo >>$seq.full
#cat $PCP_PMCDLOG_PATH >>$seq.full
echo
echo "Trace of observed state changes and PMDA count ..."
egrep '(state changes)|( value )' $tmp.pmval \
| _filter_host \
| uniq
echo
echo "primary logger ..."
echo 'connect primary
log mandatory off { pmcd.numagents sample.milliseconds }
flush' \
| pmlc
sleep 2
# if desperate!
#echo >>$seq.full
#echo "pmlogger log ..." >>$seq.full
#_filter_pmlogger_log <$LOGGING_DIR/$LOCALHOST/pmlogger.log >>$seq.full
echo "archive contents ..."
pmafm $LOGGING_DIR/$LOCALHOST/Latest pmdumplog >$tmp.out 2>&1
egrep '(<mark>)|(pmcd.numagents)' $tmp.out \
| _filter_pmdumplog \
| uniq
# note clip after 4 filtered lines to avoid extra values that sometimes
# appear due to non-determinism in pmlogger fetch samples
#
echo
echo "sanity check with pmval | filter ..."
pmafm $LOGGING_DIR/$LOCALHOST/Latest pmval -t 1 sample.milliseconds 2>&1 \
| _filter_pmval \
| sed -e 4q
# if desperate!
#echo >>$seq.full
#echo "unfiltered pmval live output" >>$seq.full
#cat $tmp.pmval >>$seq.full
# if desperate!
#echo >>$seq.full
#echo "unfiltered pmval archive output" >>$seq.full
#pmafm $LOGGING_DIR/$LOCALHOST/Latest pmval -t 1 sample.milliseconds >>$seq.full 2>&1
status=0
exit
|