/usr/share/isdn/default/ipppd.DEVICE is in ipppd 1:3.25+dfsg1-3.3ubuntu2.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 | # Options file for ipppd.
# ipppd will not read /etc/ppp/options or /etc/ppp/ioptions or any other
# config file. Everything has to be in here.
# REMOVE the next line once configuration is complete #########################
# Warning! not configured yet!
# REMOVE the above line once configuration is complete ########################
# "peer" is the name for our syncppp partner.
# STANDARD OPTIONS
#debug # enable debugging
#kdebug X # set kernel debugging level to X
#nodetach # (no) fork to the background
#callback X # ask for callback (parameter X ?)
#lock # create a lock file for device
#domain X # add domain X to a given hostname
#pidfile X # save pid in file X
#call X # take options from privileges file (???)
#idle X # idle time limit (seconds)
#holdoff X # holdoff time limit (seconds)
#maxconnect X # set maximum connection time (in seconds ?)
#+mp # enable multi line ppp
#+pwlog # log password (WARNING: possible security hole)
#nomagic # magic number negotiation
# ppp handshake : tuning
#silent # don't even try to initiate the connection
#passive # wait for the peer to initiate the connection
#lcp-echo-failure X # consecutive echo failures
#lcp-echo-interval X # time for lcp echo events
lcp-restart 1 # Set timeout for LCP
#lcp-max-terminate X # Set max #xmits for term-reqs
#lcp-max-configure X # Set max #xmits for conf-reqs
#lcp-max-failure X # Set max #conf-naks for LCP
# AUTHENTICATION
name X # set local name for auth XXX_
#user X # set name for auth with peer; default is value for name
#usehostname # use hostname for auth
#remotename X # set remote name for auth
#noauth # (dont) require peer (the other) to auth
#require-pap # allow only pap authentication (dialin only)
#require-chap # allow only chap authentication (dialin only)
#login # use system password database for pap
#papcrypt # pap passwords are encrypted
# AUTHENTICATION TUNING
#pap-restart X # Set retransmit timeout for PAP
#pap-max-authreq X # Set max #xmits for auth-reqs
#pap-timeout X # Set time limit for peer PAP auth.
#chap-restart X # Set timeout for CHAP
#chap-max-challenge X # Set max #xmits for challenge
#chap-interval X # Set interval for rechallenge
# COMPRESSION
#noaccomp # address compression on/off
#nopcomp # protocol field compression on/off
#novj # van jacobsen compression on/off
#novjccomp # van jacobsen connection-ID compression on/off
#vj-max-slots X # tune maximum vj header slots
#nobsdcomp # bsd compression on/off
#nodeflate # deflate compression on/off
#nopredictor1 # predictor1 compression in/off
noccp # compression negotation on/off
nolzs # LZS compression off (not yet supported fully)
# IP NETWORKING
#noip # (do not) disable ip transfer
#X:Y # (do not) set local ip to X, remote ip to Y
noipdefault # do not use name for default ip addr
#useifip # (do) use ip addresses from interface
#usefirstip # (do) use first ip from auth file for remote
netmask 255.255.255.255 # do set netmask, 255.255.255.255 for pointopoint
#defaultroute # (do not) set default route (for Debian config, don't uncomment)
nohostroute # do not set host route
#proxyarp # (do not) set an proxy arp entry
mru 1524 # do set maximum size of receive units to X
#default-mru # (do not) enable mru negotation
mtu 1500 # do set max size of transmit units (1500 is OK)
#useifmtu # (do not) use mtu from interface
#ipparam X # (do not) set ip parameters in script X
#ms-dns X # (do not) set dns addr for the peers use (dialin only)
#ms-wins X # (do not) wins address for the peers use (dialin only)
#ms-get-dns # (do not) accept peers suggestion of dns addr (dialout)
#set_userip # (do not) define valid ip addrs in /etc/ppp/useriptab
#ipcp-restart X # Set timeout for IPCP
#ipcp-max-terminate X # Set max #xmits for term-reqs
#ipcp-max-configure X # Set max #xmits for conf-reqs
#ipcp-max-failure X # Set max #conf-naks for IPCP
ipcp-accept-local # Accept peer's address for us
ipcp-accept-remote # Accept peer's address for it
# IPX NETWORKING
#noipx # en/disable ipx
#ipx-network X # IPX network number
#ipxcp-accept-network # Accept peer netowrk
#ipx-node X # IPX node number
#ipxcp-accept-local # Accept our address
#ipxcp-accept-remote # Accept peer's address
#ipx-routing X # IPX routing proto number
#ipx-router-name X # IPX router name
#ipxcp-restart X # Set timeout for IPXCP
#ipxcp-max-terminate X # max #xmits for term-reqs
#ipxcp-max-configure X # max #xmits for conf-reqs
#ipxcp-max-failure X # max #conf-naks for IPXCP
|