/usr/share/xemacs-21.4.22/etc/DEBUG is in xemacs21-support 21.4.22-4ubuntu3.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 | Debugging GNU Emacs
Copyright (c) 1985 Richard M. Stallman.
Permission is granted to anyone to make or distribute verbatim copies
of this document as received, in any medium, provided that the
copyright notice and permission notice are preserved,
and that the distributor grants the recipient permission
for further redistribution as permitted by this notice.
Permission is granted to distribute modified versions
of this document, or of portions of it,
under the above conditions, provided also that they
carry prominent notices stating who last changed them.
On 4.2 you will probably find that dbx does not work for
debugging GNU Emacs. For one thing, dbx does not keep the
inferior process's terminal modes separate from its own.
For another, dbx does not put the inferior in a separate
process group, which makes trouble when an inferior uses
interrupt input, which GNU Emacs must do on 4.2.
dbx has also been observed to have other problems,
such as getting incorrect values for register variables
in stack frames other than the innermost one.
The Emacs distribution now contains GDB, the new source-level
debugger for the GNU system. GDB works for debugging Emacs.
GDB currently runs on vaxes under 4.2 and on Sun 2 and Sun 3
systems.
** Some useful techniques
`Fsignal' is a very useful place to stop in.
All Lisp errors go through there.
It is useful, when debugging, to have a guaranteed way
to return to the debugger at any time. If you are using
interrupt-driven input, which is the default, then Emacs is using
RAW mode and the only way you can do it is to store
the code for some character into the variable stop_character:
set stop_character = 29
makes Control-] (decimal code 29) the stop character.
Typing Control-] will cause immediate stop. You cannot
use the set command until the inferior process has been started.
Put a breakpoint early in `main', or suspend the Emacs,
to get an opportunity to do the set command.
If you are using cbreak input (see the Lisp function set-input-mode),
then typing Control-g will cause a SIGINT, which will return control
to the debugger immediately unless you have done
ignore 3 (in dbx)
or handle 3 nostop noprint (in gdb)
You will note that most of GNU Emacs is written to avoid
declaring a local variable in an inner block, even in
cases where using one would be the cleanest thing to do.
This is because dbx cannot access any of the variables
in a function which has even one variable defined in an
inner block. A few functions in GNU Emacs do have variables
in inner blocks, only because I wrote them before realizing
that dbx had this problem and never rewrote them to avoid it.
I believe that GDB does not have such a problem.
** Examining Lisp object values.
When you have a live process to debug, and it has not encountered a
fatal error, you can use the GDB command `pr'. First print the value
in the ordinary way, with the `p' command. Then type `pr' with no
arguments. This calls a subroutine which uses the Lisp printer.
If you can't use this command, either because the process can't run
a subroutine or because the data is invalid, you can fall back on
lower-level commands.
Use the `xtype' command to print out the data type of the last data
value. Once you know the data type, use the command that corresponds
to that type. Here are these commands:
xint xptr xwindow xmarker xoverlay xmiscfree xintfwd xboolfwd xobjfwd
xbufobjfwd xkbobjfwd xbuflocal xbuffer xsymbol xstring xvector xframe
xwinconfig xcompiled xcons xcar xcdr xsubr xprocess xfloat xscrollbar
Each one of them applies to a certain type or class of types.
(Some of these types are not visible in Lisp, because they exist only
internally.)
Each x... command prints some information about the value, and
produces a GDB value (subsequently available in $) through which you
can get at the rest of the contents.
In general, most of the rest of the contents will be addition Lisp
objects which you can examine in turn with the x... commands.
** If GDB does not run and your debuggers can't load Emacs.
On some systems, no debugger can load Emacs with a symbol table,
perhaps because they all have fixed limits on the number of symbols
and Emacs exceeds the limits. Here is a method that can be used
in such an extremity. Do
nm -n temacs > nmout
strip temacs
adb temacs
0xd:i
0xe:i
14:i
17:i
:r -l loadup (or whatever)
It is necessary to refer to the file `nmout' to convert
numeric addresses into symbols and vice versa.
It is useful to be running under a window system.
Then, if Emacs becomes hopelessly wedged, you can create
another window to do kill -9 in. kill -ILL is often
useful too, since that may make Emacs dump core or return
to adb.
** Debugging incorrect screen updating.
To debug Emacs problems that update the screen wrong, it is useful
to have a record of what input you typed and what Emacs sent to the
screen. To make these records, do
(open-dribble-file "~/.dribble")
(open-termscript "~/.termscript")
The dribble file contains all characters read by Emacs from the
terminal, and the termscript file contains all characters it sent to
the terminal. The use of the directory `~/' prevents interference
with any other user.
If you have irreproducible display problems, put those two expressions
in your ~/.emacs file. When the problem happens, exit the Emacs that
you were running, kill it, and rename the two files. Then you can start
another Emacs without clobbering those files, and use it to examine them.
|