plainbox-provider-checkbox 0.4-1 / usr / share / 2013.com.canonical.certification:checkbox / jobs / led.txt.in

plugin: manual
id: led/power
_description:
 PURPOSE:
     Power LED verification
 STEPS:
     1. Power LED should be on while device is switched on
 VERIFICATION:
     Does the power LED light as expected?

plugin: manual
id: led/power-blink-suspend
depends: suspend/suspend_advanced
_description:
 PURPOSE:
     Power LED verification
 STEPS:
     1. The Power LED should blink or change color while the system is suspended
 VERIFICATION:
     Did the Power LED blink or change color while the system was suspended for the previous suspend test?

plugin: manual
id: led/suspend
_description:
 PURPOSE:
     Suspend LED verification.
 STEPS:
     Skip this test if your system does not have a dedicated Suspend LED.
     1. The Suspend LED should blink or change color while the system is
     suspended
 VERIFICATION
     Did the Suspend LED blink or change color while the system was suspended?

plugin: manual
id: led/battery-charging
_description:
 PURPOSE:
     Validate that the battery light shows charging status
 STEPS:
     1. Let system run on battery for a while
     2. Plug in AC plug
 VERIFICATION:
     Did the battery indicator LED turn orange?

plugin: manual
id: led/battery-charged
_description:
 PURPOSE:
     Validate that the battery LED properly displays charged status
 STEPS:
     1. Let system run on battery for a short time
     2. Plug in AC
     3. Let system run on AC
 VERIFICATION:
     Does the orange battery LED shut off when system is fully charged?

plugin: manual
id: led/battery-low
_description:
 PURPOSE:
     Validate that the battery LED indicated low power
 STEPS:
     1. Let system run on battery for several hours
     2. Monitor battery LED carefully
 VERIFICATION:
     Does the LED light orange when battery is low?

plugin: user-interact-verify
id: led/hdd
command: led_hdd_test
_description:
 PURPOSE:
     HDD LED verification
 STEPS:
     1. Select "Test" to write and read a temporary file for a few seconds
     2. HDD LED should light when writing to/reading from HDD
 VERIFICATION:
     Did the HDD LED light?

plugin: user-interact-verify
id: led/numeric-keypad
command: keyboard_test
_description:
 PURPOSE:
     Numeric keypad LED verification
 STEPS:
     1. Press "Block Num" key to toggle numeric keypad LED
     2. Click on the "Test" button to open a window to verify your typing
     3. Type using the numeric keypad both when the LED is on and off
 VERIFICATION:
     1. Numeric keypad LED status should toggle everytime the "Block Num" key is pressed
     2. Numbers should only be entered in the keyboard verification window when the LED is on

plugin: manual
id: led/caps-lock
_description:
 PURPOSE:
     Block cap keys LED verification
 STEPS:
     1. Press "Block Cap Keys" to activate/deactivate cap keys blocking
     2. Cap Keys LED should be switched on/off every time the key is pressed
 VERIFICATION:
     Did the Cap Keys LED light as expected?

plugin: manual
id: led/wlan
depends: keys/wireless
_description:
 PURPOSE:
     WLAN LED verification
 STEPS:
     1. During the keys/wireless test you should have observed the
     wireless LED while turning wireless back on.
     2. WLAN LED should light or change color when wireless is turned on
 VERIFICATION:
     Did the WLAN LED turn on or change color as expected?

plugin: manual
id: led/wlan-disabled
depends: keys/wireless
_description:
 PURPOSE:
     Validate that WLAN LED shuts off when disabled
 STEPS:
     1. During the keys/wireless test you should have observed the WLAN LED
     while performing that test after turning wireless off.
     2. WLAN LED should turn off or change color when wireless is turned off
 VERIFICATION:
     Did the WLAN LED turn off or change color as expected?

plugin: manual
id: led/bluetooth
depends: bluetooth/detect-output
_description:
 PURPOSE:
     Validate that the Bluetooth LED turns on and off when BT is enabled/disabled
 STEPS:
     1. Switch bluetooth off from a hardware switch (if present)
     2. Switch bluetooth back on
     3. Switch bluetooth off from the panel applet
     4. Switch bluetooth back on
 VERIFICATION:
     Did the bluetooth LED turn off and on twice?

plugin: user-interact-verify
id: led/camera
depends: camera/detect
command: camera_test led
_description:
 PURPOSE:
     Camera LED verification
 STEPS:
     1. Select Test to activate camera
     2. Camera LED should light for a few seconds
 VERIFICATION:
     Did the camera LED light?

plugin: manual
id: led/touchpad
_description:
 PURPOSE:
     Touchpad LED verification
 STEPS:
     1. Click on the touchpad button or press key combination to enable/disable touchpad button
     2. Slide your finger on the touchpad
 VERIFICATION:
     1. Touchpad LED status should toggle everytime the button is clicked or the key combination is pressed
     2. When the LED is on, the mouse pointer should move on touchpad usage
     3. When the LED is off, the mouse pointer should not move on touchpad usage

plugin: manual
id: led/wireless
_description:
 PURPOSE:
     Wireless (WLAN + Bluetooth) LED verification
 STEPS:
     1. Make sure WLAN connection is established and Bluetooth is enabled.
     2. WLAN/Bluetooth LED should light
     3. Switch WLAN and Bluetooth off from a hardware switch (if present)
     4. Switch them back on
     5. Switch WLAN and Bluetooth off from the panel applet
     6. Switch them back on
 VERIFICATION:
     Did the WLAN/Bluetooth LED light as expected?

plugin: manual
id: led/mute
depends: keys/mute
_description:
 PURPOSE:
     Audio Mute LED verification.
 STEPS:
     Skip this test if your system does not have a special Audio Mute LED.
     1. Press the Mute key twice and observe the Audio LED to determine if it
     either turned off and on or changed colors.
 VERIFICATION:
     Did the Audio LED turn on and off change color as expected?