/usr/share/openvswitch/scripts/ovs-save is in openvswitch-switch 2.0.1+git20140120-0ubuntu2.
This file is owned by root:root, with mode 0o755.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 | #! /bin/sh
# Copyright (c) 2011, 2013 Nicira, Inc.
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
usage() {
UTIL=$(basename $0)
cat <<EOF
${UTIL}: Provides helper functions to save Open vSwitch's configuration.
usage: $0 COMMAND
Commands:
save-interfaces Outputs a shell script on stdout that will restore
the current kernel configuration of the specified
network interfaces, as well as the system iptables
configuration.
save-flows Outputs a shell script on stdout that will restore
Openflow flows of each Open vSwitch bridge.
save-ofports Outputs a shell script on stdout that will restore
the ofport value across a force-reload-kmod.
This script is meant as a helper for the Open vSwitch init script commands.
EOF
}
save_interfaces () {
if (ip -V) > /dev/null 2>&1; then :; else
echo "$0: ip not found in $PATH" >&2
exit 1
fi
if test "$#" = 0; then
exit 0
fi
devs="$@"
for dev in $devs; do
state=`ip link show dev $dev` || continue
echo "# $dev"
# Link state (Ethernet addresses, up/down, ...)
linkcmd=
case $state in
*"state UP"* | *[,\<]"UP"[,\>]* )
linkcmd="$linkcmd up"
;;
*"state DOWN"*)
linkcmd="$linkcmd down"
;;
esac
if expr "$state" : '.*\bdynamic\b' > /dev/null; then
linkcmd="$linkcmd dynamic"
fi
if qlen=`expr "$state" : '.*qlen \([0-9]+\)'`; then
linkcmd="$linkcmd txqueuelen $qlen"
fi
if hwaddr=`expr "$state" : '.*link/ether \([^ ]*\)'`; then
linkcmd="$linkcmd address $hwaddr"
fi
if brd=`expr "$state" : '.*brd \([^ ]*\)'`; then
linkcmd="$linkcmd broadcast $brd"
fi
if mtu=`expr "$state" : '.*mtu \([0-9]+\)'`; then
linkcmd="$linkcmd mtu $mtu"
fi
if test -n "$linkcmd"; then
echo ip link set dev $dev down # Required to change hwaddr.
echo ip link set dev $dev $linkcmd
fi
# IP addresses (including IPv6).
echo "ip addr flush dev $dev 2>/dev/null" # Suppresses "Nothing to flush".
ip addr show dev $dev | while read addr; do
set -- $addr
# Check and trim family.
family=$1
shift
case $family in
inet | inet6) ;;
*) continue ;;
esac
# Trim device off the end--"ip" insists on having "dev" precede it.
addrcmd=
while test $# != 0; do
case $1 in
dynamic)
# Omit kernel-maintained route.
continue 2
;;
scope)
if test "$2" = link; then
# Omit route derived from IP address, e.g.
# 172.16.0.0/16 derived from 172.16.12.34.
continue 2
fi
;;
"$dev"|"$dev:"*)
# Address label string
addrcmd="$addrcmd label $1"
shift
continue
;;
esac
addrcmd="$addrcmd $1"
shift
done
if test "$1" != "$dev"; then
addrcmd="$addrcmd $1"
fi
echo ip -f $family addr add $addrcmd dev $dev
done
# Routes.
echo "ip route flush dev $dev proto boot 2>/dev/null" # Suppresses "Nothing to flush".
ip route show dev $dev | while read route; do
# "proto kernel" routes are installed by the kernel automatically.
case $route in
*" proto kernel "*) continue ;;
esac
echo "ip route add $route dev $dev"
done
echo
done
if (iptables-save) > /dev/null 2>&1; then
echo "# global"
echo "iptables-restore <<'EOF'"
iptables-save
echo "EOF"
else
echo "# iptables-save not found in $PATH, not saving iptables state"
fi
}
save_flows () {
if (ovs-ofctl --version) > /dev/null 2>&1; then :; else
echo "$0: ovs-ofctl not found in $PATH" >&2
exit 1
fi
for bridge in "$@"; do
echo "ovs-ofctl add-flows ${bridge} - << EOF"
ovs-ofctl dump-flows "${bridge}" | sed -e '/NXST_FLOW/d' \
-e 's/\(idle\|hard\)_age=[^,]*,//g'
echo "EOF"
done
}
ovs_vsctl () {
ovs-vsctl --no-wait "$@"
}
save_ofports ()
{
if (ovs-vsctl --version) > /dev/null 2>&1; then :; else
echo "$0: ovs-vsctl not found in $PATH" >&2
exit 1
fi
for bridge in "$@"; do
count=0
for iface in `ovs_vsctl list-ifaces ${bridge}`; do
ofport=`ovs_vsctl get interface ${iface} ofport`
[ "${count}" -eq 0 ] && cmd="ovs-vsctl --no-wait"
cmd="${cmd} -- --if-exists set interface "${iface}" \
ofport_request="${ofport}""
# Run set interface command on 50 ports at a time.
count=`expr ${count} + 1`
[ "${count}" -eq 50 ] && count=0 && echo "${cmd}" && cmd=""
done
echo "${cmd}"
done
}
while [ $# -ne 0 ]
do
case $1 in
"save-flows")
shift
save_flows "$@"
exit 0
;;
"save-interfaces")
shift
save_interfaces "$@"
exit 0
;;
"save-ofports")
shift
save_ofports "$@"
exit 0
;;
-h | --help)
usage
exit 0
;;
*)
echo >&2 "$0: unknown command \"$1\" (use --help for help)"
exit 1
;;
esac
done
exit 0
|