/etc/asterisk/rpt.conf is in asterisk-config 1:1.8.10.1~dfsg-1ubuntu1.
This file is owned by root:root, with mode 0o640.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 | ; Radio Repeater / Remote Base configuration file (for use with app_rpt)
; As of app_rpt version 0.39, 12/20/2005
;
;[000] ; Node ID of first repeater
;rxchannel = DAHDI/1 ; Rx audio/signalling channel
; Note: if you use a unified interface (tx/rx on one channel), only
; specify the rxchannel and the txchannel will be assumed from the rxchannel
;txchannel = DAHDI/2 ; Tx audio/signalling channel
;duplex = 2 ; (Optional) set duplex operating mode
;; 0 = half duplex (telemetry and courtesy tones do not transmit)
;; 1 = semi-half duplex (telemetry and courtesy tones transmit, but not
;; repeated audio
;; 2 = normal full-duplex mode (Default)
;; 3 = full-duplex mode, without repeated audio from main input source
;functions = functions-repeater ; DTMF function list
;; specify this for a different function list then local when on link
;;link_functions = functions-different ; DTMF function list for link
;;phone_functions = functions-phone ; (optional) different functions for 'P' mode
;;dphone_functions = functions-dphone ; (optional) different functions for 'D' mode
;;nodes = nodes-different ; (optional) different node list
;tonezone = us ; use US tones (default)
;context = default ; dialing context for phone
;callerid = "WB6NIL Repeater" <(213) 555-0123> ; Callerid for phone calls
;idrecording = wb6nil ; id recording
;accountcode=RADIO ; account code (optional)
;funcchar = * ; function lead-in character (defaults to '*')
;endchar = # ; command mode end character (defaults to '#')
;;nobusyout=yes ; (optional) Do not busy-out reverse-patch when
; normal patch in use
;hangtime=1000 ; squelch tail hang time (in ms) (optional)
;totime=100000 ; transmit time-out time (in ms) (optional)
;idtime=30000 ; id interval time (in ms) (optional)
;politeid=30000 ; time in milliseconds before ID timer
; expires to try and ID in the tail.
; (optional, default is 30000).
;idtalkover=|iwb6nil/rpt ; Talkover ID (optional) default is none
;unlinkedct=ct2 ; unlinked courtesy tone (optional) default is none
;; The tailmessagetime,tailsquashedtime, and tailmessages need to be set
;; to support tail messages. They can be omitted otherwise.
;tailmessagetime=300000 ; Play a tail message every 5 mins
;tailsquashedtime=30000 ; If squashed by another user,
;; try again after 30 seconds
;tailmessages=msg1,msg2,msg3 ;list of messages to be played for tail message
; The default values for hangtime, time-out time, and id interval time are
; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 ms)
; respectively
;[001] ; Node ID of first repeater
;rxchannel = DAHDI/3 ; Rx audio/signalling channel
; Note: if you use a unified interface (tx/rx on one channel), only
; specify the rxchannel and the txchannel will be assumed from the rxchannel
;txchannel = DAHDI/4 ; Tx audio/signalling channel
;functions = functions-repeater ; DTMF function list
;; specify this for a different function list then local when on link
;;link_functions = functions-different ; DTMF function list for link
;;phone_functions = functions-phone ; (optional) different functions for 'P' mode
;;dphone_functions = functions-dphone ; (optional) different functions for 'D' mode
;;nodes = nodes-different ; (optional) different node list
;tonezone = us ; use US tones (default)
;context = default ; dialing context for phone
;callerid = "WB6NIL Repeater" <(213) 555-0123> ; Callerid for phone calls
;idrecording = wb6nil ; id recording
;accountcode=RADIO ; account code (optional)
;funcchar = * ; function lead-in character (defaults to '*')
;endchar = # ; command mode end character (defaults to '#')
;;nobusyout=yes ; (optional) Do not busy-out reverse-patch when
; normal patch in use
;hangtime=1000 ; squelch tail hang time (in ms) (optional)
;totime=100000 ; transmit time-out time (in ms) (optional)
;idtime=30000 ; id interval time (in ms) (optional)
;politeid=30000 ; time in milliseconds before ID timer
; expires to try and ID in the tail.
; (optional, default is 30000).
;idtalkover=|iwb6nil/rpt ; Talkover ID (optional) default is none
;unlinkedct=ct2 ; unlinked courtesy tone (optional) default is none
;[002] ; Node ID of remote base
;rxchannel = DAHDI/5 ; Rx audio/signalling channel
; Note: if you use a unified interface (tx/rx on one channel), only
; specify the rxchannel and the txchannel will be assumed from the rxchannel
;txchannel = DAHDI/6 ; Tx audio/signalling channel
;functions = functions-remote
;remote = ft897 ; Set remote=y for dumb remote or
; remote=ft897 for Yaesu FT-897 or
; remote=rbi for Doug Hall RBI1
;iobase = 0x378 ; Specify IO port for parallel port (optional)
;[functions-repeater]
;1=ilink,1 ; Specific link disconnect
;2=ilink,2 ; Specific Link connect - monitor only
;3=ilink,3 ; Specific Link connect - transceive
;4=ilink,4 ; Enter command mode on a specific link
;7=ilink,5 ; Link status
;;XX=ilink,6 ; Disconnect all links (not used here)
;80=status,1 ; System info
;81=status,2 ; Time
;82=status,3 ; app_rpt.c Version
;6=autopatchup ; Autopatch up
;0=autopatchdn ; Autopatch down
;90=cop,1 ; System warm boot
;91=cop,2 ; System enable
;92=cop,3 ; System disable
;[functions-remote]
;0=remote,1 ; Retrieve Memory
;1=remote,2 ; Set freq.
;2=remote,3 ; Set Rx PL tone.
;40=remote,100 ; Rx PL off
;41=remote,101 ; Rx PL on
;42=remote,102 ; Tx PL off
;43=remote,103 ; Tx PL on
;44=remote,104 ; Low Pwr
;45=remote,105 ; Med Pwr
;46=remote,106 ; Hi Pwr
;5=remote,5 ; Status
;[telemetry]
; Telemetry entries are shared across all repeaters
; Can be a tone sequence, morse string, or a file
;
; |t - Tone escape sequence
;
; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)
; Single frequencies are created by setting freq1 or freq2 to zero.
;
; |m - Morse escape sequence
;
; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the
; [morse] section.
;
; Follow with an alphanumeric string
;
; |i - Morse ID escape sequence
;
; Sends Morse code at the ID amplitude and ID frequency as defined in the
; [morse] section.
;
; Follow with an alphanumeric string
;ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
;ct2=|t(660,880,150,2048)
;ct3=|t(440,0,150,2048)
;ct4=|t(550,0,150,2048)
;ct5=|t(660,0,150,2048)
;ct6=|t(880,0,150,2048)
;ct7=|t(660,440,150,2048)
;ct8=|t(700,1100,150,2048)
;remotetx=|t(2000,0,75,2048)(0,0,75,0)(1600,0,75,2048);
;remotemon=|t(1600,0,75,2048)
;cmdmode=|t(900,903,200,2048)
;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
;[morse]
;speed=20 ; Approximate speed in WPM
;frequency=800 ; Morse Telemetry Frequency
;amplitude=4096 ; Morse Telemetry Amplitude
;idfrequency=330 ; Morse ID Frequency
;idamplitude=2048 ; Morse ID Amplitude
;[nodes]
;000 = context_A@foo.bar.com/1234,foo.bar.com
;001 = context_B@baz.waldo.com/4321,baz.waldo.com
;002 = context_C@pepper.salt.com/5678,pepper.salt.com,y ; this is a remote
;of course, you can also specify these with domain names, but why rely
;on DNS working unnecessarily?
;[memory]
;; this example gives you 146.460, simplex, 100.0 HZ PL, hi-power, transmit PL
;00 = 146.460,100.0,sht
;; this example gives you 146.940, minus offset, 100.0 HZ PL, low-power, no PL
;01 = 146.940,100.0,-l
; The format for these entries is: Receive-Freq,Receive-PL,Attrbutes
; Attributes: l=low power, m=medium power, h=high power, -=minus offset,
; s=simplex, +=plus offset, t=tx PL enable, r=rx PL enable
|