libvirt-bin 0.9.8-2ubuntu17 / etc / libvirt / libvirtd.conf

# Master libvirt daemon configuration file
#
# For further information consult http://libvirt.org/format.html
#
# NOTE: the tests/daemon-conf regression test script requires
# that each "PARAMETER = VALUE" line in this file have the parameter
# name just after a leading "#".

#################################################################
#
# Network connectivity controls
#

# Flag listening for secure TLS connections on the public TCP/IP port.
# NB, must pass the --listen flag to the libvirtd process for this to
# have any effect.
#
# It is necessary to setup a CA and issue server certificates before
# using this capability.
#
# This is enabled by default, uncomment this to disable it
#listen_tls = 0

# Listen for unencrypted TCP connections on the public TCP/IP port.
# NB, must pass the --listen flag to the libvirtd process for this to
# have any effect.
#
# Using the TCP socket requires SASL authentication by default. Only
# SASL mechanisms which support data encryption are allowed. This is
# DIGEST_MD5 and GSSAPI (Kerberos5)
#
# This is disabled by default, uncomment this to enable it.
#listen_tcp = 1



# Override the port for accepting secure TLS connections
# This can be a port number, or service name
#
#tls_port = "16514"

# Override the port for accepting insecure TCP connections
# This can be a port number, or service name
#
#tcp_port = "16509"


# Override the default configuration which binds to all network
# interfaces. This can be a numeric IPv4/6 address, or hostname
#
#listen_addr = "192.168.0.1"


# Flag toggling mDNS advertizement of the libvirt service.
#
# Alternatively can disable for all services on a host by
# stopping the Avahi daemon
#
# This is enabled by default, uncomment this to disable it
#mdns_adv = 0

# Override the default mDNS advertizement name. This must be
# unique on the immediate broadcast network.
#
# The default is "Virtualization Host HOSTNAME", where HOSTNAME
# is subsituted for the short hostname of the machine (without domain)
#
#mdns_name = "Virtualization Host Joe Demo"


#################################################################
#
# UNIX socket access controls
#

# Set the UNIX domain socket group ownership. This can be used to
# allow a 'trusted' set of users access to management capabilities
# without becoming root.
#
# This is restricted to 'root' by default.
unix_sock_group = "libvirtd"

# Set the UNIX socket permissions for the R/O socket. This is used
# for monitoring VM status only
#
# Default allows any user. If setting group ownership may want to
# restrict this to:
#unix_sock_ro_perms = "0777"

# Set the UNIX socket permissions for the R/W socket. This is used
# for full management of VMs
#
# Default allows only root. If PolicyKit is enabled on the socket,
# the default will change to allow everyone (eg, 0777)
#
# If not using PolicyKit and setting group ownership for access
# control then you may want to relax this to:
unix_sock_rw_perms = "0770"

# Set the name of the directory in which sockets will be found/created.
#unix_sock_dir = "/var/run/libvirt"

#################################################################
#
# Authentication.
#
#  - none: do not perform auth checks. If you can connect to the
#          socket you are allowed. This is suitable if there are
#          restrictions on connecting to the socket (eg, UNIX
#          socket permissions), or if there is a lower layer in
#          the network providing auth (eg, TLS/x509 certificates)
#
#  - sasl: use SASL infrastructure. The actual auth scheme is then
#          controlled from /etc/sasl2/libvirt.conf. For the TCP
#          socket only GSSAPI & DIGEST-MD5 mechanisms will be used.
#          For non-TCP or TLS sockets,  any scheme is allowed.
#
#  - polkit: use PolicyKit to authenticate. This is only suitable
#            for use on the UNIX sockets. The default policy will
#            require a user to supply their own password to gain
#            full read/write access (aka sudo like), while anyone
#            is allowed read/only access.
#
# Set an authentication scheme for UNIX read-only sockets
# By default socket permissions allow anyone to connect
#
# To restrict monitoring of domains you may wish to enable
# an authentication mechanism here
auth_unix_ro = "none"

# Set an authentication scheme for UNIX read-write sockets
# By default socket permissions only allow root. If PolicyKit
# support was compiled into libvirt, the default will be to
# use 'polkit' auth.
#
# If the unix_sock_rw_perms are changed you may wish to enable
# an authentication mechanism here
auth_unix_rw = "none"

# Change the authentication scheme for TCP sockets.
#
# If you don't enable SASL, then all TCP traffic is cleartext.
# Don't do this outside of a dev/test scenario. For real world
# use, always enable SASL and use the GSSAPI or DIGEST-MD5
# mechanism in /etc/sasl2/libvirt.conf
#auth_tcp = "sasl"

# Change the authentication scheme for TLS sockets.
#
# TLS sockets already have encryption provided by the TLS
# layer, and limited authentication is done by certificates
#
# It is possible to make use of any SASL authentication
# mechanism as well, by using 'sasl' for this option
#auth_tls = "none"



#################################################################
#
# TLS x509 certificate configuration
#


# Override the default server key file path
#
#key_file = "/etc/pki/libvirt/private/serverkey.pem"

# Override the default server certificate file path
#
#cert_file = "/etc/pki/libvirt/servercert.pem"

# Override the default CA certificate path
#
#ca_file = "/etc/pki/CA/cacert.pem"

# Specify a certificate revocation list.
#
# Defaults to not using a CRL, uncomment to enable it
#crl_file = "/etc/pki/CA/crl.pem"



#################################################################
#
# Authorization controls
#


# Flag to disable verification of our own server certificates
#
# When libvirtd starts it performs some sanity checks against
# its own certificates.
#
# Default is to always run sanity checks. Uncommenting this
# will disable sanity checks which is not a good idea
#tls_no_sanity_certificate = 1

# Flag to disable verification of client certificates
#
# Client certificate verification is the primary authentication mechanism.
# Any client which does not present a certificate signed by the CA
# will be rejected.
#
# Default is to always verify. Uncommenting this will disable
# verification - make sure an IP whitelist is set
#tls_no_verify_certificate = 1


# A whitelist of allowed x509  Distinguished Names
# This list may contain wildcards such as
#
#    "C=GB,ST=London,L=London,O=Red Hat,CN=*"
#
# See the POSIX fnmatch function for the format of the wildcards.
#
# NB If this is an empty list, no client can connect, so comment out
# entirely rather than using empty list to disable these checks
#
# By default, no DN's are checked
#tls_allowed_dn_list = ["DN1", "DN2"]


# A whitelist of allowed SASL usernames. The format for usernames
# depends on the SASL authentication mechanism. Kerberos usernames
# look like username@REALM
#
# This list may contain wildcards such as
#
#    "*@EXAMPLE.COM"
#
# See the POSIX fnmatch function for the format of the wildcards.
#
# NB If this is an empty list, no client can connect, so comment out
# entirely rather than using empty list to disable these checks
#
# By default, no Username's are checked
#sasl_allowed_username_list = ["joe@EXAMPLE.COM", "fred@EXAMPLE.COM" ]



#################################################################
#
# Processing controls
#

# The maximum number of concurrent client connections to allow
# over all sockets combined.
#max_clients = 20


# The minimum limit sets the number of workers to start up
# initially. If the number of active clients exceeds this,
# then more threads are spawned, upto max_workers limit.
# Typically you'd want max_workers to equal maximum number
# of clients allowed
#min_workers = 5
#max_workers = 20


# The number of priority workers. If all workers from above
# pool will stuck, some calls marked as high priority
# (notably domainDestroy) can be executed in this pool.
#prio_workers = 5

# Total global limit on concurrent RPC calls. Should be
# at least as large as max_workers. Beyond this, RPC requests
# will be read into memory and queued. This directly impact
# memory usage, currently each request requires 256 KB of
# memory. So by default upto 5 MB of memory is used
#
# XXX this isn't actually enforced yet, only the per-client
# limit is used so far
#max_requests = 20

# Limit on concurrent requests from a single client
# connection. To avoid one client monopolizing the server
# this should be a small fraction of the global max_requests
# and max_workers parameter
#max_client_requests = 5

#################################################################
#
# Logging controls
#

# Logging level: 4 errors, 3 warnings, 2 information, 1 debug
# basically 1 will log everything possible
#log_level = 3

# Logging filters:
# A filter allows to select a different logging level for a given category
# of logs
# The format for a filter is:
#    x:name
#      where name is a match string e.g. remote or qemu
# the x prefix is the minimal level where matching messages should be logged
#    1: DEBUG
#    2: INFO
#    3: WARNING
#    4: ERROR
#
# Multiple filter can be defined in a single @filters, they just need to be
# separated by spaces.
#
# e.g:
# log_filters="3:remote 4:event"
# to only get warning or errors from the remote layer and only errors from
# the event layer.

# Logging outputs:
# An output is one of the places to save logging information
# The format for an output can be:
#    x:stderr
#      output goes to stderr
#    x:syslog:name
#      use syslog for the output and use the given name as the ident
#    x:file:file_path
#      output to a file, with the given filepath
# In all case the x prefix is the minimal level, acting as a filter
#    1: DEBUG
#    2: INFO
#    3: WARNING
#    4: ERROR
#
# Multiple output can be defined, they just need to be separated by spaces.
# e.g.:
# log_outputs="3:syslog:libvirtd"
# to log all warnings and errors to syslog under the libvirtd ident

# Log debug buffer size: default 64
# The daemon keeps an internal debug log buffer which will be dumped in case
# of crash or upon receiving a SIGUSR2 signal. This setting allows to override
# the default buffer size in kilobytes.
# If value is 0 or less the debug log buffer is deactivated
#log_buffer_size = 64


##################################################################
#
# Auditing
#
# This setting allows usage of the auditing subsystem to be altered:
#
#   audit_level == 0  -> disable all auditing
#   audit_level == 1  -> enable auditing, only if enabled on host (default)
#   audit_level == 2  -> enable auditing, and exit if disabled on host
#
#audit_level = 2
#
# If set to 1, then audit messages will also be sent
# via libvirt logging infrastructure. Defaults to 0
#
#audit_logging = 1

###################################################################
# UUID of the host:
# Provide the UUID of the host here in case the command
# 'dmidecode -s system-uuid' does not provide a valid uuid. In case
# 'dmidecode' does not provide a valid UUID and none is provided here, a
# temporary UUID will be generated.
# Keep the format of the example UUID below. UUID must not have all digits
# be the same.

# NB This default all-zeros UUID will not work. Replace
# it with the output of the 'uuidgen' command and then
# uncomment this entry
#host_uuid = "00000000-0000-0000-0000-000000000000"

###################################################################
# Keepalive protocol:
# This allows libvirtd to detect broken client connections or even
# dead client.  A keepalive message is sent to a client after
# keepalive_interval seconds of inactivity to check if the client is
# still responding; keepalive_count is a maximum number of keepalive
# messages that are allowed to be sent to the client without getting
# any response before the connection is considered broken.  In other
# words, the connection is automatically closed approximately after
# keepalive_interval * (keepalive_count + 1) seconds since the last
# message received from the client.  If keepalive_interval is set to
# -1, libvirtd will never send keepalive requests; however clients
# can still send them and the deamon will send responses.  When
# keepalive_count is set to 0, connections will be automatically
# closed after keepalive_interval seconds of inactivity without
# sending any keepalive messages.
#
#keepalive_interval = 5
#keepalive_count = 5
#
# If set to 1, libvirtd will refuse to talk to clients that do not
# support keepalive protocol.  Defaults to 0.
#
#keepalive_required = 1