/var/spool/hylafax/config/zyxel-1496e-2.0 is in hylafax-server 3:6.0.6-8.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 | # $Id$
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Configuration for a ZyXEL-1496E or 2864 w/ Class 2.0 firmware.
# Firmware revisions from 6.12 on should work for the 1496E; for
# the 2864 you must have firmware rev 0.07 or later.
#
# This configuration file sets up the ZyXEL to run at 38.4 for
# both sending and receiving. RTS/CTS flow control is used on
# the tty port--you probably shouldn't use XON/XOFF. Note that
# on an SGI system the getty speed is the following non-standard
# gettydefs entry:
#
# dx_38400# B38400 # B38400 SANE TAB3 HUPCL #\r\n\n$HOSTNAME login: #dx_38400
#
# CONFIG: CLASS2.0: ZyXEL*1496*-*
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2.0 # use class 2.0 interface
ModemRate: 19200
ModemFlowControl: rtscts # default
#
ModemNoFlowCmd: AT&H0 # disable flow control
ModemHardFlowCmd: AT&H3 # hardware flow control
ModemSoftFlowCmd: AT&H4 # software flow control
ModemSetupDTRCmd: AT&D2 # DTR off causes modem to hang up
ModemSetupDCDCmd: AT&C1 # DCD tracks carrier
#
ModemSetupAACmd: AT+FAA=1 # enable in current class
#
# Additional reset commands:
#
# &B1 DTE-DCE rate is fixed at DTE setting
# &N0 Auto-negotiate highest possible DCE-DCE link rate
# &S0 DSR always on
# *F0 Deny remote configuration
# S18=2 Receive at 38400 (removed from default)
# S38.3=1 DCD on/off sequence follows UNIX standard; also
# fix receiving baud rate at S18 value
# S39=0 (avoid Class 2 compatibility hacks)
#
ModemResetCmds: AT&B1&N0&S0*F0S38.3=1S39=0
#
ModemDialCmd: ATDT%s # no '@' 'cuz then busy not recognized
NoCarrierRetrys: 3 # retry 3 times on no carrier
#
ModemSetVolumeCmd: "ATM0 ATM1L1 ATM1L3 ATM1L5 ATM1L7"
#
# Caller ID configuration setup.
#
#CallIDPattern: "CALLER NUMBER: " # pattern string for phone number info
#CallIDPattern: "CALLER NAME: " # pattern string for identity info
#
PagerSetupCmds: AT&K0&N15 # use V.22 at 1200 bps (PageNet)
#
# Rev 6.1x firmware have a bug in the ECM support so
# explicitly disable it's use. To re-enable its use just
# comment out the following line.
#
Class2DCCQueryCmd: "!(0,1),(0-5),(0-4),(0-2),(0,1),(0),(0),(0-7)"
|