/usr/include/gdcm-2.6/gdcmULAction.h is in libgdcm2-dev 2.6.6-3.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 | /*=========================================================================
*
* Copyright Insight Software Consortium
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0.txt
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
*=========================================================================*/
#ifndef GDCMULACTION_H
#define GDCMULACTION_H
#include "gdcmNetworkStateID.h"
#include "gdcmULEvent.h"
#include "gdcmULConnection.h"
namespace gdcm {
class Subject;
namespace network {
/**
* \brief ULAction
* \details A ULConnection in a given ULState can perform certain ULActions. This base class
* provides the interface for running those ULActions on a given ULConnection.
*
* Essentially, the ULConnectionManager will take this object, determined from the current
* ULState of the ULConnection, and pass the ULConnection object to the ULAction. The ULAction
* will then invoke whatever necessary commands are required by a given action.
*
* The result of a ULAction is a ULEvent (ie, what happened as a result of the action).
*
* This ULEvent is passed to the ULState, so that the transition to the next state can occur.
*
* Actions are associated with Payloads-- be thos filestreams, AETitles to establish connections,
* whatever. The actual parameters that the user will pass via an action will come through
* a Payload object, which should, in itself, be some gdcm-based object (but not all objects can
* be payloads; sending a single dataelement as a payload isn't meaningful). As such, each action
* has its own particular payload.
*
* For the sake of keeping files together, both the particular payload class and the action class
* will be defined in the same header file. Payloads should JUST be data (or streams), NO METHODS.
*
* Some actions perform changes that should raise events on the local system, and some
* actions perform changes that will require waiting for events from the remote system.
*
* Therefore, this base action has been modified so that those events are set by each action.
* When the event loop runs an action, it will then test to see if a local event was raised by the
* action, and if so, perform the appropriate subsequent action. If the action requires waiting
* for a response from the remote system, then the event loop will sit there (presumably with the
* ARTIM timer running) and wait for a response from the remote system. Once a response is
* obtained, then the the rest of the state transitions can happen.
*
*/
class ULAction {
private:
//cannot copy a ULAction
ULAction(const ULAction& inAction);
protected:
public:
ULAction() {};
//make sure destructors are virtual to avoid memory leaks
virtual ~ULAction() {};
virtual EStateID PerformAction(Subject *s, ULEvent& inEvent, ULConnection& inConnection,
bool& outWaitingForEvent, EEventID& outRaisedEvent) = 0;
};
}
}
#endif // GDCMULACTION_H
|