This file is indexed.

/etc/strongswan.d/charon/eap-radius.conf is in libcharon-extra-plugins 5.5.1-4+deb9u4.

This file is owned by root:root, with mode 0o644.

The actual contents of the file can be viewed below.

  1
  2
  3
  4
  5
  6
  7
  8
  9
 10
 11
 12
 13
 14
 15
 16
 17
 18
 19
 20
 21
 22
 23
 24
 25
 26
 27
 28
 29
 30
 31
 32
 33
 34
 35
 36
 37
 38
 39
 40
 41
 42
 43
 44
 45
 46
 47
 48
 49
 50
 51
 52
 53
 54
 55
 56
 57
 58
 59
 60
 61
 62
 63
 64
 65
 66
 67
 68
 69
 70
 71
 72
 73
 74
 75
 76
 77
 78
 79
 80
 81
 82
 83
 84
 85
 86
 87
 88
 89
 90
 91
 92
 93
 94
 95
 96
 97
 98
 99
100
101
102
eap-radius {

    # Send RADIUS accounting information to RADIUS servers.
    # accounting = no

    # Close the IKE_SA if there is a timeout during interim RADIUS accounting
    # updates.
    # accounting_close_on_timeout = yes

    # Interval in seconds for interim RADIUS accounting updates, if not
    # specified by the RADIUS server in the Access-Accept message.
    # accounting_interval = 0

    # If enabled, accounting is disabled unless an IKE_SA has at least one
    # virtual IP. Only for IKEv2, for IKEv1 a virtual IP is strictly necessary.
    # accounting_requires_vip = no

    # Use class attributes in Access-Accept messages as group membership
    # information.
    # class_group = no

    # Closes all IKE_SAs if communication with the RADIUS server times out. If
    # it is not set only the current IKE_SA is closed.
    # close_all_on_timeout = no

    # Send EAP-Start instead of EAP-Identity to start RADIUS conversation.
    # eap_start = no

    # Use filter_id attribute as group membership information.
    # filter_id = no

    # Prefix to EAP-Identity, some AAA servers use a IMSI prefix to select the
    # EAP method.
    # id_prefix =

    # Whether to load the plugin. Can also be an integer to increase the
    # priority of this plugin.
    load = yes

    # NAS-Identifier to include in RADIUS messages.
    # nas_identifier = strongSwan

    # Port of RADIUS server (authentication).
    # port = 1812

    # Base to use for calculating exponential back off.
    # retransmit_base = 1.4

    # Timeout in seconds before sending first retransmit.
    # retransmit_timeout = 2.0

    # Number of times to retransmit a packet before giving up.
    # retransmit_tries = 4

    # Shared secret between RADIUS and NAS. If set, make sure to adjust the
    # permissions of the config file accordingly.
    # secret =

    # IP/Hostname of RADIUS server.
    # server =

    # Number of sockets (ports) to use, increase for high load.
    # sockets = 1

    dae {

        # Enables support for the Dynamic Authorization Extension (RFC 5176).
        # enable = no

        # Address to listen for DAE messages from the RADIUS server.
        # listen = 0.0.0.0

        # Port to listen for DAE requests.
        # port = 3799

        # Shared secret used to verify/sign DAE messages. If set, make sure to
        # adjust the permissions of the config file accordingly.
        # secret =

    }

    forward {

        # RADIUS attributes to be forwarded from IKEv2 to RADIUS.
        # ike_to_radius =

        # Same as ike_to_radius but from RADIUS to IKEv2.
        # radius_to_ike =

    }

    # Section to specify multiple RADIUS servers.
    servers {

    }

    # Section to configure multiple XAuth authentication rounds via RADIUS.
    xauth {

    }

}