/etc/init.d/decnet is in dnet-common 2.64.
This file is owned by root:root, with mode 0o755.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 | #!/bin/sh
#
# decnet.sh
#
# Sets up the ethernet interface(s).
#
# This script MUST be run before TCP/IP is started.
#
### BEGIN INIT INFO
# Provides: dnet-common decnet
# Required-Start: $network
# Required-Stop: $network
# Default-Start: 2 3 4 5
# Default-Stop: 0 1 6
# Short-Description: Set up ethernet interface(s) for DECnet
# Description: Sets the MAC address of the ethernet card(s) for DECnet
# operation, and enables routing if requested.
### END INIT INFO
# ---------------------------------------------------------------------------
#
. /lib/lsb/init-functions
#
FLAGS="start 39 S . stop 11 1 ."
#
# Interfaces to set the MAC address of are specified in /etc/default/decnet
# The variable DNET_INTERFACES should be either set to a list of interfaces
# or "all". If it is empty then no interfaces will be modified.
#
# The MAC address *must* be set for DECnet to work so if you do not use this
# program you must do it some other way.
#
# ROUTING specifies whether we should be a endnode (0), level 1 router (1)
# or aread router (2)
#
# PRIORITY specifies the routing priority. Defaults to 32. Note VMS defaults
# to 64, max is 127.
[ ! -f /sbin/setether ] && exit 0
[ -f /etc/default/decnet ] && . /etc/default/decnet
interfaces="$DNET_INTERFACES"
ADDR="`grep executor /etc/decnet.conf 2>/dev/null | cut -f2`"
setether="/sbin/setether $ADDR $interfaces"
set_routing()
{
# Enable routing if required
if [ -n "$ROUTING" ]
then
# Set a default priority lower than VMS
if [ -z "$PRIORITY" ]
then
PRIORITY=32
fi
for i in /proc/sys/net/decnet/conf/eth[0-9]*
do
echo "$1" > $i/forwarding
echo "$PRIORITY" > $i/priority
done
fi
}
case $1 in
start)
if [ ! \( -f /etc/decnet.conf -a -n "$ADDR" \) ]
then
echo "DECnet not started as it is not configured."
exit 0
fi
# If there is no DECnet in the kernel then try to load it.
if [ ! -f /proc/net/decnet ]
then
modprobe decnet
if [ ! -f /proc/net/decnet ]
then
echo "DECnet not started as it is not in the kernel."
exit 0
fi
fi
echo -n "Starting DECnet..."
$setether
set_routing $ROUTING
echo "done."
;;
stop)
set_routing 0
;;
restart|reload|force-reload)
;;
*)
echo "Usage $0 {start|stop|restart|reload|force-reload}"
;;
esac
exit 0
|