/usr/share/doc/libcomedi-dev/dt282x.conf is in libcomedi-dev 0.10.2-2.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 | #!/bin/sh
# Configuration for dt282x driver
# ds
### Device file
DEVICE=/dev/comedi0
### Type of board
### Choose one
BOARD=dt2821 # also for -f-16se, -g-16se, etc.
#BOARD=dt2823
#BOARD=dt2824-pgh
#BOARD=dt2824-pgl
#BOARD=dt2825
#BOARD=dt2827
#BOARD=dt2828
#BOARD=dt21-ez
#BOARD=dt23-ez
#BOARD=dt24-ez
#BOARD=dt24-ez-pgl
### Option 0: Board base address
### Depends on jumper settings
IOBASE=0x240
### Option 1: IRQ
### Depends on jumper settings
### Choose one
#IRQ=0 # don't use interrupts
#IRQ=3
#IRQ=5
IRQ=7
#IRQ=10
#IRQ=15
### Option 2: first DMA channel
### Depends on jumper settings
### Choose one
DMA1=0 # don't use DMA
#DMA1=5
#DMA1=6
### Option 3: second DMA channel
### Depends on jumper settings
### Choose one
DMA2=0 # don't use secondary DMA
#DMA2=6
#DMA2=7
### Option 4: Analog Input reference
### Depends on jumper settings or type of board
### Choose one
AI_REF=0 # differential
#AI_REF=1 # single ended
### Option 5: Analog Input encoding
### Depends on jumper settings
### Choose one
AI_ENCODE=0 # straight binary
#AI_ENCODE=1 # two's complement
### Option 6: Analog Output 0 encoding
### Depends on jumper settings
### Choose one
A00_ENCODE=0 # straight binary
#AO0_ENCODE=1 # two's complement
### Option 7: Analog Output 1 encoding
### Depends on jumper settings
### Choose one
AO1_ENCODE=0 # straight binary
#AO1_ENCODE=1 # two's complement
### Option 8: Analog Input Range
### Depends on jumper settings
### Choose one
#AI_RANGE=0 # bipolar +/- 10 V
#AI_RANGE=1 # unipolar 0-10 V
#AI_RANGE=2 # bipolar +/- 5 V
#AI_RANGE=3 # unipolar 0-5 V
### Option 9: Analog Output 0 Range
### Depends on jumper settings
### Choose one
#AO0_RANGE=0 # bipolar +/- 10 V
#AO0_RANGE=1 # unipolar 0-10 V
#AO0_RANGE=2 # bipolar +/- 5 V
#AO0_RANGE=3 # unipolar 0-5 V
#AO0_RANGE=4 # bipolar +/- 2.5 V
### Option 10: Analog Output 1 Range
### Depends on jumper settings
### Choose one
#AO1_RANGE=0 # bipolar +/- 10 V
#AO1_RANGE=1 # unipolar 0-10 V
#AO1_RANGE=2 # bipolar +/- 5 V
#AO1_RANGE=3 # unipolar 0-5 V
#AO1_RANGE=4 # bipolar +/- 2.5 V
#-----------------------------------------------------------
# End of Configuration
#-----------------------------------------------------------
/usr/sbin/comedi_config $DEVICE $BOARD $IOBASE,$IRQ,$DMA1,$DMA2,$AI_REF,$AI_ENCODE,$AO0_ENCODE,$AO1_ENCODE,$AI_REF,$AO0_REF,$AI1_REF
|