This file is indexed.

/etc/asterisk/misdn.conf is in asterisk-config 1:11.13.1~dfsg-2+deb8u5.

This file is owned by root:root, with mode 0o640.

The actual contents of the file can be viewed below.

  1
  2
  3
  4
  5
  6
  7
  8
  9
 10
 11
 12
 13
 14
 15
 16
 17
 18
 19
 20
 21
 22
 23
 24
 25
 26
 27
 28
 29
 30
 31
 32
 33
 34
 35
 36
 37
 38
 39
 40
 41
 42
 43
 44
 45
 46
 47
 48
 49
 50
 51
 52
 53
 54
 55
 56
 57
 58
 59
 60
 61
 62
 63
 64
 65
 66
 67
 68
 69
 70
 71
 72
 73
 74
 75
 76
 77
 78
 79
 80
 81
 82
 83
 84
 85
 86
 87
 88
 89
 90
 91
 92
 93
 94
 95
 96
 97
 98
 99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
;
; chan_misdn sample config
;

; general section:
;
; for debugging and general setup, things that are not bound to port groups
;

[general]
;
; Sets the Path to the misdn-init.conf (for nt_ptp mode checking)
;
misdn_init=/etc/misdn-init.conf

; set debugging flag:
;   0 - No Debug
;   1 - mISDN Messages and * - Messages, and * - State changes
;   2 - Messages + Message specific Informations (e.g. bearer capability)
;   3 - very Verbose, the above + lots of Driver specific infos
;   4 - even more Verbose than 3
;
; default value: 0
;
debug=0



; set debugging file and flags for mISDNuser (NT-Stack)
;
; flags can be or'ed with the following values:
;
; DBGM_NET        0x00000001
; DBGM_MSG        0x00000002
; DBGM_FSM        0x00000004
; DBGM_TEI        0x00000010
; DBGM_L2         0x00000020
; DBGM_L3         0x00000040
; DBGM_L3DATA     0x00000080
; DBGM_BC         0x00000100
; DBGM_TONE       0x00000200
; DBGM_BCDATA     0x00000400
; DBGM_MAN        0x00001000
; DBGM_APPL       0x00002000
; DBGM_ISDN       0x00004000
; DBGM_SOCK       0x00010000
; DBGM_CONN       0x00020000
; DBGM_CDATA      0x00040000
; DBGM_DDATA      0x00080000
; DBGM_SOUND      0x00100000
; DBGM_SDATA      0x00200000
; DBGM_TOPLEVEL   0x40000000
; DBGM_ALL        0xffffffff
;

ntdebugflags=0
ntdebugfile=/var/log/misdn-nt.log


; some pbx systems do cut the L1 for some milliseconds, to avoid
; dropping running calls, we can set this flag to yes and tell
; mISDNuser not to drop the calls on L2_RELEASE
ntkeepcalls=no

; the big trace
;
; default value: [not set]
;
;tracefile=/var/log/asterisk/misdn.log


; set to yes if you want mISDN_dsp to bridge the calls in HW
;
; default value: yes
;
bridging=no


; stops dialtone after getting first digit on nt Port
;
; default value: yes
;
stop_tone_after_first_digit=yes

; whether to append overlapdialed Digits to Extension or not
;
; default value: yes
;
append_digits2exten=yes

;;; CRYPTION STUFF

; Whether to look for dynamic crypting attempt
;
; default value: no
;
dynamic_crypt=no

; crypt_prefix, what is used for crypting Protocol
;
; default value: [not set]
;
crypt_prefix=**

; Keys for cryption, you reference them in the dialplan
; later also in dynamic encr.
;
; default value: [not set]
;
crypt_keys=test,muh

;------------------------------ JITTER BUFFER CONFIGURATION --------------------------
; jbenable = yes              ; Enables the use of a jitterbuffer on the receiving side of a
                              ; SIP channel. Defaults to "no". An enabled jitterbuffer will
                              ; be used only if the sending side can create and the receiving
                              ; side can not accept jitter. The SIP channel can accept jitter,
                              ; thus a jitterbuffer on the receive SIP side will be used only
                              ; if it is forced and enabled.

; jbforce = no                ; Forces the use of a jitterbuffer on the receive side of a SIP
                              ; channel. Defaults to "no".

; jbmaxsize = 200             ; Max length of the jitterbuffer in milliseconds.

; jbresyncthreshold = 1000    ; Jump in the frame timestamps over which the jitterbuffer is
                              ; resynchronized. Useful to improve the quality of the voice, with
                              ; big jumps in/broken timestamps, usually sent from exotic devices
                              ; and programs. Defaults to 1000.

; jbimpl = fixed              ; Jitterbuffer implementation, used on the receiving side of a SIP
                              ; channel. Two implementations are currently available - "fixed"
                              ; (with size always equals to jbmaxsize) and "adaptive" (with
                              ; variable size, actually the new jb of IAX2). Defaults to fixed.

; jbtargetextra = 40          ; This option only affects the jb when 'jbimpl = adaptive' is set.
                              ; The option represents the number of milliseconds by which the new
                              ; jitter buffer will pad its size. the default is 40, so without
                              ; modification, the new jitter buffer will set its size to the jitter
                              ; value plus 40 milliseconds. increasing this value may help if your
                              ; network normally has low jitter, but occasionally has spikes.

; jblog = no                  ; Enables jitterbuffer frame logging. Defaults to "no".
;-----------------------------------------------------------------------------------

; users sections:
;
; name your sections as you wish but not "general" or "default" !
; the sections are Groups, you can dial out in extensions.conf
; with Dial(mISDN/g:extern/101) where extern is a section name,
; chan_misdn tries every port in this section to find a
; new free channel
;
; The default section is not a group section, it just contains config elements
; which are inherited by group sections.
;
[default]

; define your default context here
;
; default value: default
;
context=misdn

; language
;
; default value: en
;
language=en

;
; This option specifies a default music on hold class to
; use when put on hold if the channel's moh class was not
; explicitly set with Set(CHANNEL(musicclass)=whatever) and
; the peer channel did not suggest a class to use.
;
musicclass=default

;
; Either if we should produce DTMF Tones ourselves
;
senddtmf=yes

;
; If we should generate Ringing for chan_sip and others
;
far_alerting=no


;
; Here you can list which bearer capabilities should be allowed:
;   all                  - allow any bearer capability
;   speech               - allow speech
;   3_1khz               - allow 3.1KHz audio
;   digital_unrestricted - allow unrestricted digital
;   digital_restricted   - allow restricted digital
;   video                - allow video
;
; Example:
; allowed_bearers=speech,3_1khz
;
allowed_bearers=all

; Incoming number prefixes for the indicated Type-Of-Number.  These are
; inserted before any number (caller, dialed, connected, redirecting,
; redirection) received from the ISDN link if that number has the
; corresponding Type-Of-Number.
; See the dialplan options.
;
; default values:
;    unknownprefix=
;    internationalprefix=00
;    nationalprefix=0
;    netspecificprefix=
;    subscriberprefix=
;    abbreviatedprefix=
;
;unknownprefix=
internationalprefix=00
nationalprefix=0
;netspecificprefix=
;subscriberprefix=
;abbreviatedprefix=

; set rx/tx gains between -8 and 8 to change the RX/TX Gain
;
; default values: rxgain: 0
;                 txgain: 0
;
rxgain=0
txgain=0

; some telcos especially in NL seem to need this set to yes, also in
; switzerland this seems to be important
;
; default value: no
;
te_choose_channel=no



;
; Monitors L1 of the port.  If L1 is down it tries
; to bring it up.  The polling timeout is given in seconds.
; Setting the value to 0 disables monitoring L1 of the port.
;
; default value: 0
;
; This option is only read at chan_misdn loading time.
; You need to unload and load chan_misdn to change the
; value.  An asterisk restart will also do the trick.
;
l1watcher_timeout=0

;
; This option defines, if chan_misdn should check the L1 on  a PMP
; before making a group call on it. The L1 may go down for PMP Ports
; so we might need this.
; But be aware! a broken or plugged off cable might be used for a group call
; as well, since chan_misdn has no chance to distinguish if the L1 is down
; because of a lost Link or because the Provider shut it down...
;
; default: no
;
pmp_l1_check=no


;
; in PMP this option defines which cause should be sent out to
; the 3. caller. chan_misdn does not support callwaiting on TE
; PMP side. This allows to modify the RELEASE_COMPLETE cause
; at least.
;
reject_cause=16


;
; Send Setup_Acknowledge on incoming calls anyway (instead of PROCEEDING),
; this requests additional Infos, so we can waitfordigits
; without much issues. This works only for PTP Ports
;
; default value: no
;
need_more_infos=no


;
; set this to yes if you want to disconnect calls when a timeout occurs
; for example during the overlapdial phase
;
nttimeout=no

; Set the method to use for channel selection:
;   standard     - Use the first free channel starting from the lowest number.
;   standard_dec - Use the first free channel starting from the highest number.
;   round_robin  - Use the round robin algorithm to select a channel. Use this
;                  if you want to balance your load.
;
; default value: standard
;
method=standard


; specify if chan_misdn should collect digits before going into the
; dialplan, you can choose yes=4 Seconds, no, or specify the amount
; of seconds you need;
;
overlapdial=yes

;
; dialplan means Type Of Number in ISDN Terms
; There are different types of the dialplan:
;
; dialplan -> for outgoing call's dialed number
; localdialplan -> for outgoing call's callerid
;       (if -1 is set use the value from the asterisk channel)
; cpndialplan -> for incoming call's connected party number sent to caller
;       (if -1 is set use the value from the asterisk channel)
;
; dialplan options:
;
; 0 - unknown
; 1 - International
; 2 - National
; 3 - Network-Specific
; 4 - Subscriber
; 5 - Abbreviated
;
; default value: 0
;
dialplan=0
localdialplan=0
cpndialplan=0



;
; turn this to no if you don't mind correct handling of Progress Indicators
;
early_bconnect=yes


;
; turn this on if you like to send Tone Indications to a Incoming
; isdn channel on a TE Port. Rarely used, only if the Telco allows
; you to send indications by yourself, normally the Telco sends the
; indications to the remote party.
;
; default: no
;
incoming_early_audio=no

; uncomment the following to get into s extension at extension conf
; there you can use DigitTimeout if you can't or don't want to use
; isdn overlap dial.
; note: This will jump into the s exten for every exten!
;
; default value: no
;
;always_immediate=no

;
; set this to yes if you want to generate your own dialtone
; with always_immediate=yes, else chan_misdn generates the dialtone
;
; default value: no
;
nodialtone=no


; uncomment the following if you want callers which called exactly the
; base number (so no extension is set) jump to the s extension.
; if the user dials something more it jumps to the correct extension
; instead
;
; default value: no
;
;immediate=no

; uncomment the following to have hold and retrieve support
;
; default value: no
;
;hold_allowed=yes

; Pickup and Callgroup
;
; default values: not set = 0
; range: 0-63
;
;callgroup=1
;pickupgroup=1

; Named pickup groups and named call groups
;
; give a name to groups and configure any number of groups
;
;namedcallgroup=engineering,sales,netgroup,protgroup
;namedpickupgroup=sales

; Set the outgoing caller id to the value.
;callerid="name" <number>

;
; these are the exact isdn screening and presentation indicators
; if -1 is given for either value the presentation indicators are used
; from asterisks CALLERPRES function.
; s=0, p=0 -> callerid presented
; s=1, p=1 -> callerid restricted (the remote end does not see it!)
;
; default values s=-1, p=-1
presentation=-1
screen=-1

; Incoming calls will have a caller ID tag set to this value
;
;incoming_cid_tag = "asterisk"

; With this set, you can automatically append the MSN of a party
; to the cid_tag. Incoming calls have the dialed number appended
; to the tag, and outgoing calls have the caller number appended
; to the tag. An '_' is used to separate the tag from the
; MSN.
; Default is no.
;
;append_msn_to_cid_tag = no

; Select what to do with outgoing COLP information on this port.
;
; 0 - Send out COLP information unaltered. (default)
; 1 - Force COLP to restricted on all outgoing COLP information.
; 2 - Do not send COLP information.
outgoing_colp=0

; Put a display ie in the CONNECT message containing the following
; information if it is available (nt port only):
;
; 0 - Do not put the connected line information in the display ie.
; 1 - Put the available connected line name in the display ie.
; 2 - Put the available connected line number in the display ie.
; 3 - Put the available connected line name and number in the display ie.
;
display_connected=0

; Put a display ie in the SETUP message containing the following
; information if it is available (nt port only):
;
; 0 - Do not put the caller information in the display ie.
; 1 - Put the available caller name in the display ie.
; 2 - Put the available caller number in the display ie.
; 3 - Put the available caller name and number in the display ie.
;
display_setup=0

; This enables echo cancellation with the given number of taps.
; Be aware: Move this setting only to outgoing portgroups!
; A value of zero turns echo cancellation off.
;
; possible values are: 0,32,64,128,256,yes(=128),no(=0)
;
; default value: no
;
;echocancel=no

;
; chan_misdns jitterbuffer, default 4000
;
jitterbuffer=4000

;
; change this threshold to enable dejitter functionality
;
jitterbuffer_upper_threshold=0


;
; change this to yes, if you want to bridge a mISDN data channel to
; another channel type or to an application.
;
hdlc=no


;
; defines the maximum amount of incoming calls per port for
; this group. Calls which exceed the maximum will be marked with
; the channel variable MAX_OVERFLOW. It will contain the amount of
; overflowed calls
;
max_incoming=-1

;
; defines the maximum amount of outgoing calls per port for this group
; exceeding calls will be rejected
;
max_outgoing=-1

;
; Enable/disable the call-completion retention option support (ptp only).
;
; Note: To use the CCBS/CCNR supplementary service feature and other
; supplementary services using FACILITY messages requires a
; modified version of mISDN from:
; http://svn.digium.com/svn/thirdparty/mISDN/trunk
; http://svn.digium.com/svn/thirdparty/mISDNuser/trunk
;
cc_request_retention=yes

[intern]
; define your ports, e.g. 1,2 (depends on mISDN-driver loading order)
ports=1,2
; context where to go to when incoming Call on one of the above ports
context=Intern

[internPP]
;
; adding the postfix 'ptp' to a port number is obsolete now, chan_misdn
; parses /etc/misdn-init.conf and sets the ptp mode to the corresponding
; configs. For backwards compatibility you can still set ptp here.
;
ports=3

[first_extern]
; again port defs
ports=4
; again a context for incoming calls
context=Extern1
; msns for te ports, listen on those numbers on the above ports, and
; indicate the incoming calls to asterisk
; here you can give a comma separated list or simply an '*' for
; any msn.
msns=*

; here an example with given msns
[second_extern]
ports=5
context=Extern2
callerid="Asterisk" <1234>
msns=102,144,101,104